It is a sad fact of life that where there is moisture in the air then there is a real possibility that valuable machine tools will succumb to rusting. In my workshop I am fortunate as I have not had any problems with rusting over the last 30 years and I thought it may be of interest to see why. In my opinion the key things are environment, constant temperature, few windows, low moisture, cover machinery and use of an oily rag on machine surfaces.
The workshop environment is key and my workshop is a double car-sized garage which is part of the house with the main living room above. The garage has a single large window on one side which is away from any machinery and a wide north facing up-and-over door. The door is a commercially made unit which is fully internally insulated and has rubber seals. This door is remarkable in that it is just over 1" thick yet heat loss is minimal. As it faces north there is no sun to warm it up so by and large the workshop keeps to within a 10-16deg. C range year round.
Maintaining a constant temperature is essential and changes should occur very slowly. If temperature changes happen quickly by using external heating then moisture will condense onto colder metal surfaces and rust will soon appear.
Maintaining a low level of moisture inside the workshop is ideal and the use of a dehumidifier will help however I do not use a dehumidifier and also park the car inside the garage even when it is covered with rain drops. So why do my machines not rust when there is evidently a lot of moisture in the air? The constant temperature is again a major reason but I also cover my machines with these 'blue' polyethylene woven tarpaulin water resistant sheets which are readily available and very low cost. These sheets are arranged so that they prevent any moisture droplets getting onto a machine surface but crucially allow a free passage of air. Never use cotton or any covering that absorbs water!
If there is a need to raise the temperature of the workshop then this must be done very gradually to allow the cold metal to also heat up. Never use propane or similar heaters as they produce a lot of water.
The final step is to keep an oily rag available and give the machine surfaces a quick wipe if the workshop is not going to be used for a week or so.
See my website for more information: http://www.gwhengineering.co.uk
Tuesday 23 December 2014
Monday 22 December 2014
So what is gh creative engineering
So what is creative engineering?
I studied engineering many years ago but got side tracked into a computing career mainly because engineering jobs were low paid and difficult to find. The creative aspects within this new and emerging world of computing stayed with me until I retired. Unfortunately, whilst computers were and are fascinating, my true passion was always engineering. Despite a demanding job I had a basic home workshop and whenever there was time I was able to spend time making models and tooling. Now retired, my hobby is my main interest and decided to build some models and workshop tools. This brings me on to explain the 'creative' aspect of my engineering hobby.
It is quite enjoyable to build a model from acquired plans but sometimes the tools available in my workshop were 'limited' which often presented difficulties. The answer was to adapt my equipment and 'create' tools to overcome as far as possible the build of models. This aspect of the hobby is, for me, the most interesting because it is creative. To design tools and machines to meet a requirement presents many challenges but is very rewarding.
My most significant 'creative engineering' design and build is that of an automatic spur gear involute profiling machine. This machine operates using the concept used in the Sunderland gear machine. My starting point was just a single paragraph in one of my old text books describing the operating concept and a picture of the Sunderland machine. The operating concept is simple and by means of a 'generative process' it produces accurate complex involute curves. My machine is a small bench top version which adopts the same operating concept but thereafter the design is unique and all created from just a few words in a book. The journey from design to completion has taken several years with many obstacles needing to be solved but this is the best part of creating a new machine and then making it so that it works.
See my website for more information: http://www.gwhengineering.co.uk
I studied engineering many years ago but got side tracked into a computing career mainly because engineering jobs were low paid and difficult to find. The creative aspects within this new and emerging world of computing stayed with me until I retired. Unfortunately, whilst computers were and are fascinating, my true passion was always engineering. Despite a demanding job I had a basic home workshop and whenever there was time I was able to spend time making models and tooling. Now retired, my hobby is my main interest and decided to build some models and workshop tools. This brings me on to explain the 'creative' aspect of my engineering hobby.
It is quite enjoyable to build a model from acquired plans but sometimes the tools available in my workshop were 'limited' which often presented difficulties. The answer was to adapt my equipment and 'create' tools to overcome as far as possible the build of models. This aspect of the hobby is, for me, the most interesting because it is creative. To design tools and machines to meet a requirement presents many challenges but is very rewarding.
My most significant 'creative engineering' design and build is that of an automatic spur gear involute profiling machine. This machine operates using the concept used in the Sunderland gear machine. My starting point was just a single paragraph in one of my old text books describing the operating concept and a picture of the Sunderland machine. The operating concept is simple and by means of a 'generative process' it produces accurate complex involute curves. My machine is a small bench top version which adopts the same operating concept but thereafter the design is unique and all created from just a few words in a book. The journey from design to completion has taken several years with many obstacles needing to be solved but this is the best part of creating a new machine and then making it so that it works.
See my website for more information: http://www.gwhengineering.co.uk
Subscribe to:
Posts (Atom)